Видео

Did you check the earthing resistance with a relevant tester?

Bhai ek baar Mera wala Jake dekhiye

Thank you sooo much you gite me great thanks a lot❤😊❤❤😊😊❤

Subscribe now 💡⚡💸💲

Dp switch ra normal switch ma k Farak chha?

Very helpful,let me repaire my extention box👍💪

Ye series wiring hai ya parallel

Hi bro 😊

that won't handle much current

सुंदर

Thanks , but if I don't join an earth wire any problem in two pin 🔌

Vary nice

Nice learne.

Dono switch ke upper wale points short karna zarori hai

❤🔥super

I love electrical work ❤

Those are dangerous because they do not have a ground wire. I would never use that without protection. There are others that do come with it, a little more expensive but safe.

Esos don malos y peligrosos.porque no traen el cable a tierra..jamas lo pondria.hay otris que si lo traen

Bahut sunder

ভাইয়া এটা দুই মিনিট থেকে চলবে না

Mera ghar ka electric board me switch off karega tho be current a raha hay kya kare?

Good

Thanks I'm watching you from 🇸🇱

Very useful information Just now connected one socket by watching this

Very nice sir❤

This is so wrong! The rule of thumb TPV= 42/Ac (Ac = core cross section) is BS. The magnetic equation is B = (Vp x E+8)/ 4.44 X Np X Ac X f where B is the maximum usable core flux density in gauss, Vp is the primary high line voltage, Ac is the core cross section area cm sq, and f is the power line frequency. The figure 4.44 is a factor for sine wave excitation. B can range from 12,000 gauss for thick laminations (24 ga) to 17,500 gauss for thin (29ga) laminations. Tape wound toroids are made of even higher quality silicon steel with B max up to 17,800 gauss. Compare calculated numbers using this formula to the rule of thumb. I designed power transformers for 15yrs!

ياريت يكون شرح المكونات بالعربيه

भाई इस तरह से कनेक्शन करने रेगुलेटर में एनीटाइम करंट रहेगा

Right sir 👍🤝

Video bnane wala ko chordana chahiye

Banane ko kaise bhi ban jayga lekin jo tareeka hai waise nahi banaya

AaaaaaaaaaaaaaaaaaaAaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaAaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaAAAAAAAAAaaaaaaaaaaaaaaaaaAaaaaaaAaaaaaaaaaaaaaAaaawa.

The 1st switch and the last switch should work, alternate

Good ❤🎉

Good 🎉❤

what is the value of resistance after doing this?

❤🎉🎉🎉🎉

❤❤❤❤❤❤❤❤❤❤❤🎉

good but had it been more effective if wire would have been bolted directly with the copper strip rather than with the aluminium strip.

Super video bro

Nice 🎉🎉🎉🎉🎉

👍👍👍👍

Mu me zuban nhi hai ky 😒 Video me bol e ko ky hota kana ?

ভাই ভিডিওতে মিউজিকটা না দিয়ে আপনি বলে বলে কথা বলে বুঝিয়ে দিতেন

which drill bit size u used for making hole??😊

Deep atleast 4 to 5 feet nesecasry ,it's wrong proses in your video

Thank you so much.

❤❤👉👉🙏👉📱

❤❤